Wikipedia

Silicone

(Redirected from Polysiloxane)
Not to be confused with the chemical element silicon.

In organosilicon and polymer chemistry, a silicone or polysiloxane is a polymer composed of repeating units of siloxane (−O−R2Si−O−SiR2−, where R = organic group). They are typically colorless oils or rubber-like substances. Silicones are used in sealants, adhesives, lubricants, medicine, cooking utensils, thermal insulation, and electrical insulation. Some common forms include silicone oil, grease, rubber, resin, and caulk.[1][2]

Silicone caulk can be used as a basic sealant against water and air penetration.

Chemistry

edit
Main article: Organosilicon compound
 
Chemical structure of the silicone polydimethylsiloxane (PDMS)

Alfred Stock and Carl Somiesky examined the hydrolysis of dichlorosilane, a reaction that was proposed to initially give the monomer H2SiO:   When the hydrolysis is performed by treating a solution of H2SiCl2 in benzene with water, the product was determined to have the approximate formula [H2SiO]6. Higher polymers were proposed to form with time.[3]

Most polysiloxanes feature organic substituents, e.g., [(CH3)2SiO]n and [(C6H5)2SiO)]n. All polymerized siloxanes or polysiloxanes, silicones consist of an inorganic silicon–oxygen backbone chain (···−Si−O−Si−O−Si−O−···) with two groups attached to each silicon center. The materials can be cyclic or polymeric. By varying the −Si−O− chain lengths, side groups, and crosslinking, silicones can be synthesized with a wide variety of properties and compositions. They can vary in consistency from liquid to gel to rubber to hard plastic. The most common siloxane is linear polydimethylsiloxane (PDMS), a silicone oil.[citation needed] The second-largest group of silicone materials is based on silicone resins, which are formed by branched and cage-like oligosiloxanes.[citation needed]

Terminology and history

edit

F. S. Kipping coined the word silicone in 1901 to describe the formula of polydiphenylsiloxane, Ph2SiO (Ph = phenyl, C6H5), by analogy with the formula of the ketone benzophenone, Ph2CO (his term was originally silicoketone). Kipping was well aware that polydiphenylsiloxane is polymeric[citation needed] whereas benzophenone is monomeric and noted the contrasting properties of Ph2SiO and Ph2CO.[4][5] The discovery of the structural differences between Kipping's molecules and the ketones means that silicone is no longer the correct term (though it remains in common usage) and that the term siloxane is preferred according to the nomenclature of modern chemistry.[6]

James Franklin Hyde (born 11 March 1903) was an American chemist and inventor. He has been called the "Father of Silicones" and is credited with the launch of the silicone industry in the 1930s. His most notable contributions include his creation of silicone from silicon compounds and his method of making fused silica, a high-quality glass later used in aeronautics, advanced telecommunications, and computer chips. His work led to the formation of Dow Corning, an alliance between the Dow Chemical Company and Corning Glass Works that was specifically created to produce silicone products.

Silicone is often confused with silicon, but they are distinct substances. Silicon is a chemical element, a hard dark-grey semiconducting metalloid, which in its crystalline form is used to make integrated circuits ("electronic chips") and solar cells. Silicones are compounds that contain silicon, carbon, hydrogen, oxygen, and perhaps other kinds of atoms as well, and have many very different physical and chemical properties.

Compounds containing silicon–oxygen double bonds, now called silanones, but which could deserve the name "silicone", have long been identified as intermediates in gas-phase processes such as chemical vapor deposition in microelectronics production, and in the formation of ceramics by combustion.[7] However, they have a strong tendency to polymerize into siloxanes. The first stable silanone was obtained in 2014 by A. Filippou and others.[8]

Synthesis

edit

Most common are materials based on polydimethylsiloxane, which is derived by hydrolysis of dimethyldichlorosilane. This dichloride reacts with water as follows:

 

The polymerization typically produces linear chains capped with Si−Cl or Si−OH (silanol) groups. Under different conditions, the polymer is a cyclic, not a chain.[1]

For consumer applications such as caulks, silyl acetates are used instead of silyl chlorides. The hydrolysis of the acetates produces the less dangerous acetic acid (the acid found in vinegar) as the reaction product of a much slower curing process. This chemistry is used in many consumer applications, such as silicone caulk and adhesives.

 

Branches or crosslinks in the polymer chain can be introduced by using organosilicone precursors with fewer alkyl groups, such as methyl trichlorosilane and methyltrimethoxysilane. Ideally, each molecule of such a compound becomes a branch point. This process can be used to produce hard silicone resins. Similarly, precursors with three methyl groups can be used to limit molecular weight, since each such molecule has only one reactive site and so forms the end of a siloxane chain.

Combustion

edit

When silicone is burned in air or oxygen, it forms solid silica (silicon dioxide, SiO2) as a white powder, char, and various gases. The readily dispersed powder is sometimes called silica fume. The pyrolysis of certain polysiloxanes under an inert atmosphere is a valuable pathway towards the production of amorphous silicon oxycarbide ceramics, also known as polymer derived ceramics. Polysiloxanes terminated with functional ligands such as vinyl, mercapto or acrylate groups have been cross linked to yield preceramic polymers, which can be photopolymerised for the additive manufacturing of polymer derived ceramics by stereolithography techniques.[9]

Properties

edit
 
This silicone rubber folding chessboard resists creasing and wrinkling.

Silicones exhibit many useful characteristics, including:[1]

  • Low thermal conductivity
  • Low chemical reactivity
  • Low toxicity
  • Thermal stability (constancy of properties over a wide temperature range of −100 to 250 °C)
  • The ability to repel water and form watertight seals.
  • Does not stick to many substrates, but adheres very well to others, e.g. glass
  • Does not support microbiological growth
  • Resistance to creasing and wrinkling
  • Resistance to oxygen, ozone, and ultraviolet (UV) light. This property has led to the widespread use of silicones in the construction industry (e.g. coatings, fire protection, glazing seals) and the automotive industry (external gaskets, external trim).
  • Electrical insulation properties. Because silicone can be formulated to be electrically insulative or conductive, it is suitable for a wide range of electrical applications.
  • High gas permeability: at room temperature (25 °C), the permeability of silicone rubber for such gases as oxygen is approximately 400 times[10] that of butyl rubber, making silicone useful for medical applications in which increased aeration is desired. Conversely, silicone rubbers cannot be used where gas-tight seals are necessary such as seals for high-pressure gasses or high vacuum.

Silicone can be developed into rubber sheeting, where it has other properties, such as being FDA compliant. This extends the uses of silicone sheeting to industries that demand hygiene, for example, food and beverage, and pharmaceuticals.

Applications

edit

Silicones are used in many products. Ullmann's Encyclopedia of Industrial Chemistry lists the following major categories of application: Electrical (e.g. insulation), electronics (e.g., coatings), household (e.g., sealants and cooking utensils), automobile (e.g. gaskets), airplane (e.g., seals), office machines (e.g. keyboard pads), medicine and dentistry (e.g. tooth impression molds), textiles and paper (e.g. coatings). For these applications, an estimated 400,000 tonnes of silicones were produced in 1991.[clarification needed] Specific examples, both large and small are presented below.[1]

Automotive

edit
 
Silicone caulks and rubber components are often used in automotive applications.

In the automotive field, silicone grease is typically used as a lubricant for brake components since it is stable at high temperatures, is not water-soluble, and is far less likely than other lubricants to foul. DOT 5 brake fluids are based on liquid silicones.

Automotive spark plug wires are insulated by multiple layers of silicone to prevent sparks from jumping to adjacent wires, causing misfires. Silicone tubing is sometimes used in automotive intake systems (especially for engines with forced induction).

Sheet silicone is used to manufacture gaskets used in automotive engines, transmissions, and other applications.

Automotive body manufacturing plants and paint shops avoid silicones, as trace contamination may cause "fish eyes", which are small, circular craters which mar a smooth finish.[citation needed]

Additionally, silicone compounds such as silicone rubber are used as coatings and sealants for airbags; the high strength of silicone rubber makes it an optimal adhesive and sealant for high impact airbags.[citation needed] Silicones in combination with thermoplastics provide improvements in scratch and mar resistance and lowered coefficient of friction.[citation needed]

Aerospace

edit
 
Silicone is often used to seal maintenance access openings in aerospace equipment.

Silicone is a widely used material in the aerospace industry due to its sealing properties, stability across an extreme temperature range, durability, sound dampening and anti-vibration qualities, and naturally flame retardant properties. Maintaining extreme functionality is paramount for passenger safety in the aerospace industry, so each component on an aircraft requires high-performance materials.

Specially developed aerospace grades of silicone are stable from −70 to 220 °C,[11] these grades can be used in the construction of gaskets for windows and cabin doors. During operation, aircraft go through large temperature fluctuations in a relatively short period of time; from the ambient temperatures when on the ground in hot countries to sub-zero temperatures when flying at high altitude. Silicone rubber can be molded with tight tolerances ensuring gaskets form airtight seals both on the ground and in the air, where atmospheric pressure decreases.

Silicone rubber's resistance to heat corrosion enables it to be used for gaskets in aircraft engines where it will outlast other types of rubber, both improving aircraft safety and reducing maintenance costs. The silicone acts to seal instrument panels and other electrical systems in the cockpit, protecting printed circuit boards from the risks of extreme altitude such as moisture and extremely low temperature. Silicone can be used as a sheath to protect wires and electrical components from any dust or ice that may creep into a plane's inner workings.

As the nature of air travel results in much noise and vibration, powerful engines, landings, and high speeds all need to be considered to ensure passenger comfort and safe operation of the aircraft. As silicone rubber has exceptional noise reduction and anti-vibration properties, it can be formed into small components and fitted into small gaps ensuring all equipment can be protected from unwanted vibration such as overhead lockers, vent ducts, hatches, entertainment system seals, and LED lighting systems.

Solid propellant

edit

Polydimethylsiloxane (PDMS) based binders along with ammonium perchlorate (NH4ClO4) are used as fast burning solid propellants in rockets.[12]

Building construction

edit

The strength and reliability of silicone rubber are widely acknowledged in the construction industry. One-part silicone sealants and caulks are in common use to seal gaps, joints and crevices in buildings. One-part silicones cure by absorbing atmospheric moisture, which simplifies installation. In plumbing, silicone grease is typically applied to O-rings in brass taps and valves, preventing lime from sticking to the metal.

Structural silicone has also been used in curtain wall building façades since 1974 when the Art Institute of Chicago became the first building to receive exterior glass fixed only with the material.[citation needed] Silicone membranes have been used to cover and restore industrial roofs, thanks to its extreme UV resistance, and ability to keep their waterproof performance for decades.[citation needed]

3D printing

edit
 
Silicone 3D print with support material

Silicone rubber can be 3D printed (liquid deposition modelling, LDM) using pump-nozzle extrusion systems. Standard silicone formulations are optimized to be used by extrusion and injection moulding machines and are not applicable in LDM-based 3D printing. The rheological behavior and the pot life need to be adjusted for use with LDM.[13]

3D printing also requires the use of a removable support material that is compatible with the silicone rubber.

Coatings

edit

Silicone films can be applied to such silica-based substrates as glass to form a covalently bonded hydrophobic coating. Such coatings were developed for use on aircraft windshields to repel water and to preserve visibility, without requiring mechanical windshield wipers which are impractical at supersonic speeds. Similar treatments were eventually adapted to the automotive market in products marketed by Rain-X and others.

Many fabrics can be coated or impregnated with silicone to form a strong, waterproof composite such as silnylon.

A silicone polymer can be suspended in water by using stabilizing surfactants. This allows water-based formulations to be used to deliver many ingredients that would otherwise require a stronger solvent, or be too viscous to use effectively. For example, a waterborne formulation using a silane's reactivity and penetration ability into a mineral-based surface can be combined with water-beading properties from a siloxane to produce a more-useful surface protection product.

Cookware

edit

As a low-taint, non-toxic material, silicone can be used where contact with food is required. Silicone is becoming an important product in the cookware industry, particularly bakeware and kitchen utensils. Silicone is used as an insulator in heat-resistant potholders and similar items; however, it is more conductive of heat than similar less dense fiber-based products. Silicone oven gloves are able to withstand temperatures up to 260 °C (500 °F), making it possible to reach into boiling water.

Other products include molds for chocolate, ice, cookies, muffins, and various other foods; non-stick bakeware and reusable mats used on baking sheets; steamers, egg boilers or poachers; cookware lids, pot holders, trivets, and kitchen mats.

  •  
    Soup ladle and pasta ladle made of silicone
  •  
    A silicone food steamer to be placed inside a pot of boiling water
  •  
    Flexible ice cube trays made of silicone allow easy extraction of ice.
  •  
    Silicone brush used for basting and applying flavoring liquids

Defoaming

edit

Silicones are used as active compounds in defoamers due to their low water solubility and good spreading properties.

Dry cleaning

edit

Liquid silicone can be used as a dry cleaning solvent, providing an alternative to the traditional chlorine-containing perchloroethylene (perc) solvent. The use of silicones in dry cleaning reduces the environmental effect of a typically high-polluting industry.[citation needed]

Electronics

edit
 
Silicone rubber keypad

Electronic components are sometimes encased in silicone to increase stability against mechanical and electrical shock, radiation and vibration, a process called "potting". Silicones are used where durability and high performance are demanded of components under extreme environmental conditions, such as in space (satellite technology). They are selected over polyurethane or epoxy encapsulation when a wide operating temperature range is required (−65 to 315 °C). Silicones also have the advantage of little exothermic heat rise during cure, low toxicity, good electrical properties, and high purity.

Silicones are often components of thermal pastes used to improve heat transfer from power-dissipating electronic components to heat sinks.

The use of silicones in electronics is not without problems, however. Silicones are relatively expensive and can be attacked by certain solvents. Silicone easily migrates as either a liquid or vapor onto other components. Silicone contamination of electrical switch contacts can lead to failures by causing an increase in contact resistance, often late in the life of the contact, well after any testing is completed.[14][15] Use of silicone-based spray products in electronic devices during maintenance or repairs can cause later failures.

Firestops

edit
 
Red-colored silicone firestopping

Silicone foam has been used in North American buildings in an attempt to firestop openings within the fire-resistance-rated wall and floor assemblies to prevent the spread of flames and smoke from one room to another. When properly installed, silicone-foam firestops can be fabricated for building code compliance. Advantages include flexibility and high dielectric strength. Disadvantages include combustibility (hard to extinguish) and significant smoke development.

Silicone-foam firestops have been the subject of controversy and press attention due to smoke development from pyrolysis of combustible components within the foam, hydrogen gas escape, shrinkage, and cracking. These problems have led to reportable events among licensees (operators of nuclear power plants) of the Nuclear Regulatory Commission (NRC).[citation needed]

Silicone firestops are also used in aircraft.

Jewelry

edit

Silicone is a popular alternative to traditional metals (such as silver and gold) with jewelry, specifically rings. Silicone rings are commonly worn in professions where metal rings can lead to injuries, such as electrical conduction and ring avulsions.[16][17] During the mid-2010's, some professional athletes began wearing silicone rings as an alternative during games.[18]

Lubricants

edit
 
Silicone grease is often used with laboratory glassware to prevent seizing.

Silicone greases are used for many purposes, such as bicycle chains, airsoft gun parts, and a wide range of other mechanisms. Typically, a dry-set lubricant is delivered with a solvent carrier to penetrate the mechanism. The solvent then evaporates, leaving a clear film that lubricates but does not attract dirt and grit as much as an oil-based or other traditional "wet" lubricant.

Silicone personal lubricants are also available for use in medical procedures or sexual activity.

Medicine and cosmetic surgery

edit

Silicone is used in microfluidics, seals, gaskets, shrouds, and other applications requiring high biocompatibility. Additionally, the gel form is used in bandages and dressings, breast implants, testicle implants, pectoral implants, contact lenses, and a variety of other medical uses.

Scar treatment sheets are often made of medical grade silicone due to its durability and biocompatibility. Polydimethylsiloxane (PDMS) is often used for this purpose, since its specific crosslinking results in a flexible and soft silicone with high durability and tack. It has also been used as the hydrophobic block of amphiphilic synthetic block copolymers used to form the vesicle membrane of polymersomes.

Illicit cosmetic silicone injections may induce chronic and definitive silicone blood diffusion with dermatologic complications.[19]

Ophthalmology uses many products such as silicone oil used to replace the vitreous humor following vitrectomy, silicone intraocular lenses following cataract extraction, silicone tubes to keep a nasolacrimal passage open following dacryocystorhinostomy, canalicular stents for canalicular stenosis, punctal plugs for punctal occlusion in dry eyes, silicone rubber and bands as an external tamponade in tractional retinal detachment, and anteriorly-located break in rhegmatogenous retinal detachment.

Addition and condensation (e.g. polyvinyl siloxane) silicones find wide application as a dental impression material due to its hydrophobic property and thermal stability.[20][21][22]

Moldmaking

edit
 
Silicone mold used to reproduce an architectural detail

Two-part silicone systems are used as rubber molds to cast resins, foams, rubber, and low-temperature alloys. A silicone mold generally requires little or no mold-release or surface preparation, as most materials do not adhere to silicone. For experimental uses, ordinary one-part silicone can be used to make molds or to mold into shapes. If needed, common vegetable cooking oils or petroleum jelly can be used on mating surfaces as a mold-release agent.[23]

Silicone cooking molds used as bakeware do not require coating with cooking oil; in addition, the flexibility of the rubber allows the baked food to be easily removed from the mold after cooking.

Personal care

edit
 
Silicone rubber earplugs for hearing protection

Silicones are ingredients widely used in skincare, color cosmetic and hair care applications. Some silicones, notably the amine functionalized amodimethicones, are excellent hair conditioners, providing improved compatibility, feel, and softness, and lessening frizz. The phenyl dimethicones, in another silicone family, are used in reflection-enhancing and color-correcting hair products, where they increase shine and glossiness (and possibly impart subtle color changes). Phenyltrimethicones, unlike the conditioning amodimethicones, have refractive indices (typically 1.46) close to that of a human hair (1.54). However, if included in the same formulation, amodimethicone and phenyltrimethicone interact and dilute each other, making it difficult to achieve both high shine and excellent conditioning in the same product.[24]

Silicone rubber is commonly used in baby bottle nipples (teats) for its cleanliness, aesthetic appearance, and low extractable content.

Silicones are used in shaving products and personal lubricants.[25]

Toys and hobbies

edit
 
Baby toys made of nontoxic silicone rubber

Silly Putty and similar materials are composed of silicones dimethyl siloxane, polydimethylsiloxane, and decamethyl cyclopentasiloxane, with other ingredients. This substance is noted for its unusual characteristics, e.g., that it bounces, but breaks when given a sharp blow; it will also flow like a liquid and form a puddle given enough time.

Silicone "rubber bands" are a long-lasting popular replacement refill for real rubber bands in the 2013 fad "rubber band loom" toys at two to four times the price (in 2014). Silicone bands also come in bracelet sizes that can be custom embossed with a name or message. Large silicone bands are also sold as utility tie-downs.

Formerol is a silicone rubber (marketed as Sugru) used as an arts-and-crafts material, as its plasticity allows it to be molded by hand like modeling clay. It hardens at room temperature and it is adhesive to various substances including glass and aluminum.[26]

Oogoo is an inexpensive silicone clay, which can be used as a substitute for Sugru.[27]

In making aquariums, manufacturers now commonly use 100% silicone sealant to join glass plates. Glass joints made with silicone sealant can withstand great pressure, making obsolete the original aquarium construction method of angle-iron and putty. This same silicone is used to make hinges in aquarium lids or for minor repairs. However, not all commercial silicones are safe for aquarium manufacture, nor is silicone used for the manufacture of acrylic aquariums as silicones do not have long-term adhesion to plastics.[28]

Special Effects

edit

Silicone is used in special effects as a material for simulating realistic skin, either for prosthetic makeup, prop body parts, or rubber masks.[29] Platinum silicones are ideal for simulating flesh and skin due to their strength, firmness, and translucency, creating a convincing effect. Silicone masks have an advantage over latex masks in that because of the material properties, the mask hugs the wearers face and moves in a realistic manner with the wearer's facial expressions.[30] Silicone is often used as a hypoallergenic substitute for foam latex prosthetics.

Marketing

edit

The leading global manufacturers of silicone base materials belong to three regional organizations: the European Silicone Center (CES) in Brussels, Belgium; the Silicones Environmental, Health, and Safety Center (SEHSC) in Herndon, Virginia, US; and the Silicone Industry Association of Japan (SIAJ) in Tokyo, Japan. Dow Corning Silicones, Evonik Industries, Momentive Performance Materials, Milliken and Company (SiVance Specialty Silicones), Shin-Etsu Silicones, Wacker Chemie, Bluestar Silicones, JNC Corporation, Wacker Asahikasei Silicone, and Dow Corning Toray represent the collective membership of these organizations. A fourth organization, the Global Silicone Council (GSC) acts as an umbrella structure over the regional organizations. All four are non-profit, having no commercial role; their primary missions are to promote the safety of silicones from a health, safety, and environmental perspective. As the European chemical industry is preparing to implement the Registration, Evaluation, and Authorisation of Chemicals (REACH) legislation, CES is leading the formation of a consortium[31] of silicones, silanes, and siloxanes producers and importers to facilitate data and cost-sharing.

Safety and environmental considerations

edit

Silicone compounds are pervasive in the environment. Particular silicone compounds, cyclic siloxanes D4 and D5, are air and water pollutants and have negative health effects on test animals.[32] They are used in various personal care products. The European Chemicals Agency found that "D4 is a persistent, bioaccumulative and toxic (PBT) substance and D5 is a very persistent, very bioaccumulative (vPvB) substance".[33][34] Other silicones biodegrade readily, a process that is accelerated by a variety of catalysts, including clays.[1] Cyclic silicones have been shown to involve the occurrence of silanols during biodegradation in mammals.[clarification needed][35] The resulting silanediols and silanetriols are capable of inhibiting hydrolytic enzymes such as thermolysin, acetylcholinesterase. However, the doses required for inhibition are by orders of magnitude higher than the ones resulting from the accumulated exposure to consumer products containing cyclomethicone.[36][37]

At around 200 °C (392 °F) in an oxygen-containing atmosphere, polydimethylsiloxane releases traces of formaldehyde (but lesser amounts than other common materials such as polyethylene[38][39]). At this temperature, silicones were found to have lower formaldehyde generation than mineral oil and plastics (less than 3 to 48 μg CH2O/(g·hr) for a high consistency silicone rubber, versus around 400 μg CH2O/(g·hr) for plastics and mineral oil). By 250 °C (482 °F), copious amounts of formaldehyde have been found to be produced by all silicones (1,200 to 4,600 μg CH2O/(g·hr)).[39]

See also

edit

References

edit
  1. ^ a b c d e Moretto, Hans-Heinrich; Schulze, Manfred; Wagner, Gebhard (2005). "Silicones". Ullmann's Encyclopedia of Industrial Chemistry. Weinheim: Wiley-VCH. doi:10.1002/14356007.a24_057. ISBN 978-3527306732.
  2. ^ Fink, Johannes Karl (5 July 2019). Liquid Silicone Rubber: Chemistry, Materials, and Processing. John Wiley & Sons. ISBN 9781119631378.
  3. ^ Seyferth, D., Prud'Homme, C., Wiseman, G., Cyclic Polysiloxanes from the Hydrolysis of Dichlorosilane, Inorganic Chemistry, 22, 2163-2167
  4. ^ Greenwood, Norman N.; Earnshaw, Alan (1997). Chemistry of the Elements (2nd ed.). Butterworth-Heinemann. p. 362. ISBN 978-0-08-037941-8.
  5. ^ Frederic Kipping, L. L. Lloyd (1901). "XLVII. Organic derivatives of silicon. Triphenylsilicol and alkyloxysilicon chlorides". J. Chem. Soc., Trans. 79: 449–459. doi:10.1039/CT9017900449.
  6. ^ James E. Mark; Harry R. Allcock; Robert West (24 March 2005). Inorganic Polymers. Oxford University. p. 155. ISBN 978-0-19-535131-6. Archived from the original on 18 December 2017.
  7. ^ V. N. Khabashesku; Z. A. Kerzina; K. N. Kudin; O. M. Nefedov (1998). "Matrix isolation infrared and density functional theoretical studies of organic silanones, (CH3O)2Si=O and (C6H5)2Si=O". J. Organomet. Chem. 566 (1–2): 45–59. doi:10.1016/S0022-328X(98)00726-8.
  8. ^ Alexander C. Filippou, Bernhard Baars, Yury N. Lebedev, and Gregor Schnakenburg (2014): "Silicon–Oxygen Double Bonds: A Stable Silanone with a Trigonal‐Planar Coordinated Silicon Center". Angewandte Chemie International Edition, volume 53, issue 2, pages 565–570. doi:10.1002/anie.201308433.
  9. ^ Additive manufacturing of ceramics from preceramic polymers: A versatile stereolithographic approach assisted by thiol-ene click chemistry. Additive Manufacturing, (2019) volume 27, pp. 80–90.
  10. ^ "Treeing Characteristics in HTV Silicone Rubber", Electrical Insulation Breakdown and Its Theory, Process, and Prevention, Advances in Computer and Electrical Engineering, IGI Global, pp. 73–104, 2020, doi:10.4018/978-1-5225-8885-6.ch003, ISBN 978-1-5225-8885-6, S2CID 241551199, retrieved 2021-03-16
  11. ^ "Aerospace | Viking Extrusions". www.vikingextrusions.co.uk. Retrieved 2019-04-11.
  12. ^ Eisele, Siegfried; Gerber, Peter; Menke, Klaus (June 2002). <161::aid-prep161>3.0.co;2-4 "Fast Burning Rocket Propellants Based on Silicone Binders – New Aspects of an Old System". Propellants, Explosives, Pyrotechnics. 27 (3): 161. doi:10.1002/1521-4087(200206)27:3<161::aid-prep161>3.0.co;2-4. ISSN 0721-3115.
  13. ^ Courtial, Edwin-Joffrey; Perrinet, Clément; Colly, Arthur; Mariot, David; Frances, Jean-Marc; Fulchiron, René; Marquette, Christophe (2019-08-01). "Silicone rheological behavior modification for 3D printing: Evaluation of yield stress impact on printed object properties". Additive Manufacturing. 28: 50–57. doi:10.1016/j.addma.2019.04.006. ISSN 2214-8604. S2CID 146407873.
  14. ^ Paul G. Slade (1999). "16.4.1". Electrical Contacts: Principles and Applications. CRC Press. p. 823. ISBN 978-0-8247-1934-0. Archived from the original on 2017-12-18.
  15. ^ W. Witter & R. Leiper (1979). "A Comparison for the Effects of Various Forms of Silicon Contamination on Contact Performance". IEEE Transactions on Components, Hybrids, and Manufacturing Technology. 2: 56–61. doi:10.1109/TCHMT.1979.1135411.
  16. ^ Ashley, Sarah (August 1, 2018). "Is the Silicone Ring Trend Here to Stay?".
  17. ^ Chen, Connie. "A ton of couples are skipping the fancy wedding rings and opting for these $20 rubber bands instead — here's why". Insider.
  18. ^ "The (wedding) ring's the thing: Silicone bands a growing trend in NFL". ESPN.com. September 29, 2016.
  19. ^ Bertin, Chloé; Abbas, Rachid; Andrieu, Valérie; Michard, Florence; Rioux, Christophe; Descamps, Vincent; Yazdanpanah, Yazdan; Bouscarat, Fabrice (January 2019). "Illicit massive silicone injections always induce chronic and definitive silicone blood diffusion with dermatologic complications". Medicine. 98 (4): e14143. doi:10.1097/MD.0000000000014143. PMC 6358378. PMID 30681578.
  20. ^ "The many uses of dental impression silicone". July 19, 2022. Retrieved January 16, 2023.
  21. ^ Ferracane, Jack L. (2001). Materials in dentistry : principles and applications (2nd ed.). Philadelphia: Lippincott Williams & Wilkins. ISBN 0-7817-2733-2. OCLC 45604030.
  22. ^ Sturdevant's art and science of operative dentistry. André V. Ritter, Clifford M. Sturdevant (7 ed.). St. Louis. 2018. ISBN 978-0-323-47858-8. OCLC 1124496192.{{cite book}}: CS1 maint: location missing publisher (link) CS1 maint: others (link)
  23. ^ Robyn Lish. What are the benefits of Silicone Caulk Moulds. Myheap.com. Retrieved on 2021-08-08.
  24. ^ Thomas Clausen et al. "Hair Preparations" in Ullmann's Encyclopedia of Industrial Chemistry, 2007, Wiley-VCH, Weinheim. doi:10.1002/14356007.a12_571.pub2
  25. ^ Q. Ashton Acton: Silicones—Advances in Research and Application: 2013 Edition, ScholarlyEditions, 2013, ISBN 9781481692397, p. 226 Archived 2017-12-18 at the Wayback Machine.
  26. ^ " "Formerol/Sugru technical data sheet".
  27. ^ "How to Make Your Own Sugru Substitute". Instructables.
  28. ^ "Aquarium Silicone Applications". Aquarium-pond-answers.com. March 2007. Archived from the original on 2012-03-15. Retrieved 2012-02-28.
  29. ^ Chant, Justin. "Unmasking the Chemistry Behind Special Effects Makeup". www.monarchchemicals.co.uk. Retrieved 29 July 2024.
  30. ^ Chapman, Kit. "What are Halloween costume masks made from?". RSC Education. Retrieved 29 July 2024.
  31. ^ "REACH consortium". Reach.silicones.eu. Archived from the original on 2012-03-15. Retrieved 2012-02-28.
  32. ^ Bienkowski, Brian (30 April 2013). "Chemicals from Personal Care Products Pervasive in Chicago Air". Scientific American. Archived from the original on 20 June 2015. Retrieved 8 April 2015.
  33. ^ European Chemicals Agency. "Committee for Risk Assessment concludes on restricting D4 and D5". European Chemicals Agency. Retrieved 28 August 2018.
  34. ^ "ECHA classifies cyclic siloxanes as SVHCs". Food Packaging Forum Foundation. 25 June 2018. Retrieved 28 August 2018.
  35. ^ S. Varaprath, K. L. Salyers, K. P. Plotzke and S. Nanavati: "Identification of Metabolites of Octamethylcyclotetrasiloxane (D4) in Rat Urine", Drug Metab Dispos 1999, 27, 1267-1273.
  36. ^ S. M. Sieburth, T. Nittoli, A. M. Mutahi and L. Guo: Silanediols: a new class of potent protease inhibitors, Angew. Chem. Int. Ed. 1998, volume 37, 812-814.
  37. ^ M. Blunder, N. Hurkes, M. List, S. Spirk and R. Pietschnig: Silanetriols as in vitro AChE Inhibitors, Bioorg. Med. Chem. Lett. 2011, volume 21, 363-365.
  38. ^ Hard, Dave. "Dielectric Fluids for Transformer Cooling — History and Types". General Electric. Archived from the original on 2016-07-19.
  39. ^ a b David C. Timpe Jr. Formaldehyde Generation from Silicone Rubber Archived 2015-04-27 at the Wayback Machine Arlon
edit
 
Look up silicone in Wiktionary, the free dictionary.
Retrieved from "https://en.wikipedia.org/w/index.php?title=Silicone&oldid=1260650341"
  NODES
Association 1
Idea 2
idea 2
INTERN 1
Note 3