A toothed belt, timing belt, cogged belt, cog belt, or synchronous belt is a flexible belt with teeth moulded onto its inner surface. Toothed belts are usually designed to run over matching toothed pulleys or sprockets. Toothed belts are used in a wide array of mechanical devices where high power transmission is desired.

Supercharger drive belt in a dragster

Design and application

edit

Timing belts,[1] toothed belts,[2] cogged or cog belts,[3] and synchronous belts[4] are non-slipping mechanical drive belts. They are made as flexible belts with teeth moulded onto their inner surface. The belts run over matching toothed pulleys or sprockets.[5][6][7] When correctly tensioned, these type of belts have no slippage, and are often used to transfer motion for indexing or timing purposes (hence their name). They are often used in lieu of chains or gears, so there is less noise and a lubrication bath is not necessary.

Toothed belts are used widely in mechanical devices, including sewing machines, photocopiers and many others. A major use of toothed belts is as the timing belt used to drive the camshafts within an automobile or motorcycle engine.

As toothed belts can deliver more power than a friction-drive belt, they are used for high-power transmissions. These include the primary drive of some motorcycles, notably later Harley-Davidsons; and the supercharger used for dragsters.

Microlight aircraft driven by high-speed two-stroke engines such as the Rotax 532 use toothed belt reduction drives to allow the use of a quieter and more efficient slower-speed propeller. Some amateur-built airplanes powered by automotive engines use cog belt reduction drive units.[8]

Other names

edit

A gilmer belt was a brand or trade name for a mechanical belt used for transferring power between axles in a machine. The gilmer belt was originally sold by the L. H. Gilmer company after 1949,[9] and represents one of the earliest toothed belt designs. Gilmer belts use trapezoidal teeth to engage matching grooves on toothed pulleys in order to maintain synchronicity between moving parts.[10] Belts are no longer sold under the Gilmer name, although enthusiasts are still likely to refer to toothed belts by the gilmer name.[11]

Fabrication

edit

Toothed belts are made of a flexible polymer over a fabric reinforcement. Originally this was rubber over a natural textile, but developments in material science have had a substantial effect in increasing the lifetime of these belts. This included changes from natural to synthetic rubber and polyurethane and also the adoption of steel, nylon, Kevlar (or other aramid fibres), and/or carbon fibres in their reinforcement.[2]

Belt failure

edit
 
A new belt, already damaged by knotting

Toothed belts have two failure modes, one gradual and one catastrophic. There is an increased risk of either over the lifetime of the belt, so it is common for highly-stressed belts to be given a service lifetime and to be replaced before this failure can occur.

One failure mode is gradual wear to the tooth shape, which may eventually lead to slippage over rounded teeth. The belt often continues to work, but the relative timing between shafts changes.

The catastrophic failure mode is caused by delamination between the belt and its fabric reinforcement. Although this may be caused by age and wear, it is often accelerated by mistreatment of the belt, often during initial installation. Overloading the belt by bending it to a narrow radius is a common cause of damage, either by bending out of the belt's designed axis, twisting, levering it into place with tools, bending in the correct axis but to too small a radius, or even knotting a belt in storage. Another cause, particularly with natural rubber belts, is contamination by oil, especially to the edges where the reinforcing fabric is exposed and can cause a wick effect.

It is extremely rare for a timing belt to break. More common is for the belt to delaminate, disconnecting the fabric strength member from the teeth that ride on the pulleys. The belt is then often thrown from the pulleys and may be further damaged, cut, or break. Although worn teeth may be detectable by careful inspection, internal deterioration is not considered to be reliably detectable and so the observance of service lifetimes is important.

See also

edit

References

edit
  1. ^ "Huco Timing Belts and Pulleys". Huco Dynatork.
  2. ^ a b US patent 5807194, "Toothed belt", published 15 September 1998, assigned to Gates Corporation 
  3. ^ in Contact !, Experimental Aircraft and Powerplant Newsforum for Designers and Builders, n°55, Dieselis Aircraft, A Prototype Aircraft with a Diesel Engine
  4. ^ "PowerGrip HTD and timing synchronous belts". Gates Corporation.
  5. ^ "ENG-10, Camshaft (Timing) Belt and Balance Shaft Belt Tension - Checking and Adjusting". Clarks Garage. Retrieved 2014-02-27. This should be checked at the midpoint between the cam sprocket and the crankshaft sprocket.
  6. ^ "Replacing Chrysler 2.2 and 2.5 liter engine timing belts". AllPar. Retrieved 2014-02-27. Sprockets on the cam and intermediate shaft are twice the diameter of the sprocket on the crank, so for every two turns of the crankshaft the cam and intermediate shaft is turned one time.
  7. ^ "Timing Belt Pulley Pitch Diameter & Outside Diameter Charts". Pfeifer Industries. Retrieved 2014-02-27. sprocket pitch circle
  8. ^ For example : Bede BD-5, Dieselis aircraft "DslGB001". Archived from the original on 2013-07-01. Retrieved 2013-05-12., and Pennec Gaz'Aile 2
  9. ^ Synchronous Belts - Part 1 (PDF), Gates Rubber Company, archived from the original (PDF) on 2016-08-09
  10. ^ Definition of a Gilmer belt, Isky Racing Cams, archived from the original on 2010-11-24, retrieved 2011-01-16
  11. ^ "Uniroyal to Sell Unit to Gates", The New York Times, 1986-05-22
  NODES
HOME 1
Intern 1
languages 1
mac 2
Note 1
os 2
text 1